水泥技术|ICR article draft
 Best mill practice and protection

   更新日期:2018-09-27     来源:建材之家    作者:防水之家    浏览:30    评论:0    
核心提示:Sintered cast grinding rolls are gaining greater prominence by cementmill maintenance operators, asthey do not require intermediate hard facing repair. On the other hand, some producers ha

水泥技术|生产商品混凝土对散装水泥的质量要求

推荐简介:1、商品混凝土对散装水泥出厂的要求 1.1安定性:水泥的安定性指标比其强度指标更为重要,水泥强度等级不达标准或偏低,可通过降低标号使用或调整混凝土水灰比等途径使用,但安定性不合格只能作为废品处理,严禁使用。引起水泥安定性不良的因素主要是游离氧化钙、游离氧化镁含量等。在生产中应严格控制游离氧化钙、游离氧化镁含量。水泥中石膏掺入量过多,会产生膨胀应力而影响水泥的安定性,若水泥熟料中游离氧化钙、游离氧化......
防水之家讯:Sintered cast grinding rolls are gaining greater prominence by cementmill maintenance operators, asthey do not require intermediate hard facing repair. On the other hand, some producers have been reverting to regular hard facing of mill tyres and table liners, as breakage and abnormal loss of profile is often observed on sintered cast grinding rolls. This can result in a substantial lossof throughput and an increase in power consumption compared to similar output of grinding media by Ni-Hard castings.

Analysis provided in this article looksat how both types of castings can be intelligently applied, by keeping in mind the basic objective of achieving maximum plant availability and rated mill capacity throughput.

Myth or fact?

Sintered cast rolls are non-weldable?

Myth. Where minimum sinter materialis still visible, a small amount of surface preparation will enable welding to be carried out which could potentially increase working life by 6000-8000h – resulting in substantial savings for the plant. A successful trial at a South African cement plant has already demonstrated such encouraging results. The alternative is to replace the sintered cast table liners.

Complete hardfacing of sintered castings is not possible?

Myth. With the use of gauging flux cored wires and air gauging, a clean surface can be almost be achieved, which is suitable for hardfacing. Therefore, a number of welded repairs can be carried out.

There is no loss of profile in sintered cast?

Myth. The regular interaction with plant

Many arguments have been put forward in terms of best practice for maintaining mill grinding components. The two main solutions are hardfacing and sintered cast grinding rolls and table liners. However, it is not always clear when a cement plant should weld or when to simply replace components. By dispelling some common maintenance assumptions, this article how both types of castings can be applied to ensure best mill availability.



Figure 1: worn-out sintered cast table lines

WELDING & REPAIR



Figure 2: repaired by welding for additional life

operation and maintenance engineers suggest that there is a loss of profile after a year or between 5000-6000 working hours. Plant personnel can be faced with a dilemma since they can neither repair the roller profile to restore optimum

grinding efficiency nor replace the rolls as they are not worn enough. In such cases, selection on the basis of loss of sinter from the contact surface, hardfacing can be considered by adapting partial gauging onsite and then repairing the castings.

DECEMBER 2013 ICR XX

WELDING & REPAIR

Best practice study

One collaborative study undertaken by a hardfacing services provider and a cement plant maintenance team found the following measures enabLED best mill availabiity:

Use Ni-Hard casting primarily for slag and clinker grinding, due the higher abrasive nature of both these materials Hi carbon Ni-Hard casting are best.

The reduction in profile was found to

be gradual and can be repaired while maximum life and throughput can be achieved with very low wear of less than 1g/t.

Sinter casts are good for raw mill

and coal mill grinding components. Throughput should be monitored closely and selective hardfacing be carried out to recover grinding efficiency.

Before throwing any castings, sintered or Hi carbon cast iron, consideration should be given to the saving resources given the costs involved in making new purchases. Even casting that has been

about the authors...

Abhijit Dhodapkar has worked closely with various Indian cement plants during his tenure as managing director of UK–MNC dealing in onsite hardfacing. As chairman of his new venture, FerroClad solutions, he is working with his Chinese counterparts on new collaborations using the latest techniques to repair sinter cast grinding components for cement plants in India, Africa and Middle East.

Graham Hughes has served 27 years as workshop chief for repairing grinding components. He is now general manager of Chinese Flux Cored Wire Manufacturing and Services Company, Beijing, Open Arc Welding Alloys.

Sinter casts are good

for raw mill and coal mill grinding components. However, throughput should be monitored closely and selective hardfacing can be carried out to recover grinding efficiency.

worn out up to 45mm on radius can be hardfaced with a close study of the best profile during the lifecycle of the casting. ? Losses in power consumption during and after the loss of the roll profile

need to be monitored closely so that

an informed decision can be made

and backed by efficient data collection management.

防水之家是专注防水,泥水,防水材料,防水涂料的新闻资讯和防水,防水材料,防水涂料等各十大品牌的装修效果图和网上购物商城,敬请登陆防水之家:http://fangshui.jc68.com/
小程序码
 
打赏
 
更多>文章标签:防水
更多>同类水泥防水资讯
0相关评论

推荐图文更多...
点击排行更多...
水泥防水商机更多...
水泥防水圈更多...
最新视频更多...
推荐产品更多...
家居头条 |  陶瓷头条 |  马赛克头条 |  卫浴头条 |  洁具头条 |  油漆头条 |  涂料头条 |  地板头条 |  灯具头条 |  门窗头条 |  吊顶头条 |  衣柜头条 |  五金头条 |  楼梯头条 |  墙纸头条 |  壁纸头条 |  装修头条 |  家装头条 |  涂料之窗 |  风水头条 |  深圳建材  |  揭阳建材  |  香港建材  |  佛山建材  |  福田世纪  |  广州建材  |  东莞建材  |  惠州建材  |  潮州建材  |  汕头建材  |  珠海建材  |  江门建材 |  湛江建材 |  茂名建材 |  肇庆建材 |  梅州建材 |  汕尾建材 |  河源建材 | 
关于我们  |  联系方式  |  使用协议  |  版权隐私  |  网站地图 | 排名推广 | 广告服务 | 积分换礼 | 网站留言 | RSS订阅 | sitemap | 粤ICP备14017808号
Powered by 水泥之家 (c)2015-2017 BO-YI.COM SYSTEM All Rights Reserved